For hundreds of years, the game of pool has existed in many forms. Despite the fact that there have been significant changes to materials comprising certain aspects of the game, the element that has been most consistent is the felt cover. The bad news is that the lifespan of felt covers is not always as long as that of the table itself. When it comes to pool table refelting Denver residents ought to know the basics.
Among the materials required for the replacement are a socket wrench, felts, rag, cleanser, staple gun and hammer. For a start, the staples surrounding the pockets towards the underside of the table will need to be removed. This is followed by removing the rails securing the underside through the use of a socket wrench. Approximately, the individual will need to locate three bolts for every rail.
After all the bolts have been removed, the rails will need to be taken off. This will be followed by detaching of the pocket liners. The staples that attach the felt to rail cushions will have to be pulled out. Felt covering the cushions will then need to be removed, after which it gets removed from the table top. At this stage, one has to determine if the felt gets glued or stapled, or both. The staples that are hold the felt are removed using a staple puller. Removal of the glued felt is supposed to be done very gently.
The next step is the preparation of the slate so that it is re-felted. All the cracks and holes are filled using pool table waxes. The wax will need to be left to harden for a minute or so. Any excesses are scrapped with a putty knife. It will then be important to clean the slate surface using a gentle cleanser. The surface has to dry completely before it is covered.
It is always important to measure the pieces of felt that are to be used. They are then cut according to the measured dimensions of the table. The felt edges are aligned flush with the edges of the table. It is very important that the measurements are done with utmost accuracy because failing to do so will lead to a mot so pleasant look.
After making the measurements and doing the cutting, the fabric will need to be stapled to the table. This is started from the center of any short edge and moving gradually towards the corners. During all this, the pockets ought not to be covered. During placement of the staples, the person doing the work should move in increments of roughly two inches as the fabric is pulled taut. This happens for all table sides.
There is trimming of excess fabric from the pockets. On an approximate basis, three inches of the fabric are left at the inner edges. What follows is pushing of the fabric to the pockets such that all pocket sides are lined.
There is wrapping of the rails with felt. It would be vital to observe the unique design of the rails so as to determine the size of felt pieces to use. The rails are attached to the table, and then the liners and pockets are replaced accordingly.
Among the materials required for the replacement are a socket wrench, felts, rag, cleanser, staple gun and hammer. For a start, the staples surrounding the pockets towards the underside of the table will need to be removed. This is followed by removing the rails securing the underside through the use of a socket wrench. Approximately, the individual will need to locate three bolts for every rail.
After all the bolts have been removed, the rails will need to be taken off. This will be followed by detaching of the pocket liners. The staples that attach the felt to rail cushions will have to be pulled out. Felt covering the cushions will then need to be removed, after which it gets removed from the table top. At this stage, one has to determine if the felt gets glued or stapled, or both. The staples that are hold the felt are removed using a staple puller. Removal of the glued felt is supposed to be done very gently.
The next step is the preparation of the slate so that it is re-felted. All the cracks and holes are filled using pool table waxes. The wax will need to be left to harden for a minute or so. Any excesses are scrapped with a putty knife. It will then be important to clean the slate surface using a gentle cleanser. The surface has to dry completely before it is covered.
It is always important to measure the pieces of felt that are to be used. They are then cut according to the measured dimensions of the table. The felt edges are aligned flush with the edges of the table. It is very important that the measurements are done with utmost accuracy because failing to do so will lead to a mot so pleasant look.
After making the measurements and doing the cutting, the fabric will need to be stapled to the table. This is started from the center of any short edge and moving gradually towards the corners. During all this, the pockets ought not to be covered. During placement of the staples, the person doing the work should move in increments of roughly two inches as the fabric is pulled taut. This happens for all table sides.
There is trimming of excess fabric from the pockets. On an approximate basis, three inches of the fabric are left at the inner edges. What follows is pushing of the fabric to the pockets such that all pocket sides are lined.
There is wrapping of the rails with felt. It would be vital to observe the unique design of the rails so as to determine the size of felt pieces to use. The rails are attached to the table, and then the liners and pockets are replaced accordingly.
About the Author:
You can visit www.anytimebilliards.com for more helpful information about Steps Of Pool Table Refelting Denver.
No comments:
Post a Comment